erinqr#
- Mapdl.erinqr(key, pname='__tmpvar__', **kwargs)#
Obtain information from common errors.
Warning
DISCLAIMER: This function is un-documented in the official ANSYS Command Reference Guide. Hence its support is limited and it use is not encouraged. Please use it with caution.
- Parameters:
- key
int
Item to be returned.
1 = keyerr (
ER_ERRORFLAG
)Master error flag.
2 = errfil (
ER_ERRORFILE
)Errors file unit number.
3 = numnot (
ER_NUMNOTE
)Total number of notes displayed.
4 = numwrn (
ER_NUMWARNING
)Total number of warnings displayed.
5 = numerr (
ER_NUMERROR
)Total number of errors displayed.
6 = numfat (
ER_NUMFATAL
)Total number of fatals displayed.
7 = maxmsg (
ER_MAXMESSAGE
)Max allowed number of displayed messages before abort.
8 = lvlerr (
ER_ERRORLEVEL
)Used basically in solution (from
cnvr
command.)-1 = do not set keyerr for notes/errors/warnings.
-2 = same as -1 but do not display message either.
9 = mxpcmd (
ER_MAXCOMMAND
)Maximum number of messages allowed per command.
10 = nercmd (
ER_NUMCOMMAND
)Number of messages displayed for any one command.
11 = nertim (
ER_UICLEAR
)Key as to how message cleared from u/i pop-up (only for “info” calls)
-1 = message is timed before removal
0 = message needs pick or keyboard before removal
1 = message stays up until replaced by another message
12 = nomore (
ER_NOMOREMSG
)Display no more messages
0 = display messages
1 = display discontinue message and stop displaying
13 = eropen (
ER_FILEOPEN
)0 = errors file is closed
1 = errors file is opened
14 = ikserr (
ER_INTERERROR
)0 = if interactive do not set keyerr.
-1 = if interactive set keyerr (used by mesher and tessalation)
15 = kystat (
ER_KEYOPTTEST
)Flag to bypass keyopt tests in the elcxx routines associated with status/panel info inquiries.
0 = do not bypass keyopt tests
1 = perform all keyopt tests also flag to bypass setting of
_STATUS
upon resume
16 = mxr4r5 (
ER_MIXEDREV
)Mixed rev4-rev5 input logic (
*do
,*if
,*go
,*if-go
)1 = rev5 found (
*do
,*fi-then-*endif
)2 = rev4 found (
*go
,:xxx
,*if
, ….,:xxx
)3 = warning printed. do not issue any more.
17 = mshkey (
ER_MESHING
)CPU intensive meshing etc. This will cause
nertim (11)
to be set to-1
for “notes”,1
for “warnings”,and0
for “errors”. Checking of this key is done inanserr
.0 = not meshing or cpu intensive
1 = yes, meshing or cpu intensive
18 = syerro (18)
Systop error code. read by anserr if set.
19 = opterr (
ER_OPTLOOPING
)0 = no error in main ansys during opt looping
1 = an error has happened in main ansys during opt looping
20 = flowrn (20)
Flag used by “floqa” as to list
floqa.ans
.0 = list
floqa.ans
1 =
floqa.ans
has been listed. do not list again.
22 = noreport (22)
Used in GUI for turning off errors due to strsub calls.
0 = process errors as usual
1 = do NOT report errors
23 = pdserr (
ER_PDSLOOPING
)0 = no error in main ansys during pds looping
1 = an error has happened in main ansys during pds looping
24 = mxpcmdw (24)
Number of messages written to file.err for any command
0 = write all errors to file.err
1 = only write displayed errors to file.err
25 = kystop
No information is provided.
26 = icloads (26)
Key to forbid the
iclist
command from listing solution data instead of the input data.0 =
iclist
is OK1 = do not permit
iclist
27 = ifkey error (27)
key on whether or not to abort during
/input
on error.0 = do not abort
1 = abort
28 = intrupt (
ER_INTERRUPT
)Interrupt button, so executable returns no error.
spare - spare integer variables
- pname
str
Name of the variable where the queried value is stored.
- **kwargs
Extra arguments to be passed to
Mapdl.run
.
- key
- Returns: