erinqr

Mapdl.erinqr(key, pname='__tmpvar__', **kwargs)

Obtain information from common errors.

Warning

DISCLAIMER: This function is un-documented in the official ANSYS Command Reference Guide. Hence its support is limited and it use is not encouraged. Please use it with caution.

Parameters:

keyint

Item to be returned.

• 1 = keyerr (ER_ERRORFLAG)

  Master error flag.

• 2 = errfil (ER_ERRORFILE)

  Errors file unit number.

• 3 = numnot (ER_NUMNOTE)

  Total number of notes displayed.

• 4 = numwrn (ER_NUMWARNING)

  Total number of warnings displayed.

• 5 = numerr (ER_NUMERROR)

  Total number of errors displayed.

• 6 = numfat (ER_NUMFATAL)

  Total number of fatals displayed.

• 7 = maxmsg (ER_MAXMESSAGE)

  Max allowed number of displayed messages before abort.

• 8 = lvlerr (ER_ERRORLEVEL)

  Used basically in solution (from cnvr command.)

  • -1 = do not set keyerr for notes/errors/warnings.

  • -2 = same as -1 but do not display message either.

• 9 = mxpcmd (ER_MAXCOMMAND)

  Maximum number of messages allowed per command.

• 10 = nercmd (ER_NUMCOMMAND)

  Number of messages displayed for any one command.

• 11 = nertim (ER_UICLEAR)

  Key as to how message cleared from u/i pop-up (only for “info” calls)

  • -1 = message is timed before removal

  • 0 = message needs pick or keyboard before removal

  • 1 = message stays up until replaced by another message

• 12 = nomore (ER_NOMOREMSG)

  Display no more messages

  • 0 = display messages

  • 1 = display discontinue message and stop displaying

• 13 = eropen (ER_FILEOPEN)

  • 0 = errors file is closed

  • 1 = errors file is opened

• 14 = ikserr (ER_INTERERROR)

  • 0 = if interactive do not set keyerr.

  • -1 = if interactive set keyerr (used by mesher and tessalation)

• 15 = kystat (ER_KEYOPTTEST)

  Flag to bypass keyopt tests in the elcxx routines associated with status/panel info inquiries.

  • 0 = do not bypass keyopt tests

  • 1 = perform all keyopt tests also flag to bypass setting of _STATUS upon resume

• 16 = mxr4r5 (ER_MIXEDREV)

  Mixed rev4-rev5 input logic (*do, *if , *go , *if-go)

  • 1 = rev5 found (*do, *fi-then-*endif)

  • 2 = rev4 found (*go, :xxx , *if, …., :xxx)

  • 3 = warning printed. do not issue any more.

• 17 = mshkey (ER_MESHING)

  CPU intensive meshing etc. This will cause nertim (11) to be set to -1 for “notes”, 1 for “warnings”,and 0 for “errors”. Checking of this key is done in anserr.

  • 0 = not meshing or cpu intensive

  • 1 = yes, meshing or cpu intensive

• 18 = syerro (18)

  Systop error code. read by anserr if set.

• 19 = opterr (ER_OPTLOOPING)

  • 0 = no error in main ansys during opt looping

  • 1 = an error has happened in main ansys during opt looping

• 20 = flowrn (20)

  Flag used by “floqa” as to list floqa.ans.

  • 0 = list floqa.ans

  • 1 = floqa.ans has been listed. do not list again.

• 22 = noreport (22)

  Used in GUI for turning off errors due to strsub calls.

  • 0 = process errors as usual

  • 1 = do NOT report errors

• 23 = pdserr (ER_PDSLOOPING)

  • 0 = no error in main ansys during pds looping

  • 1 = an error has happened in main ansys during pds looping

• 24 = mxpcmdw (24)

  Number of messages written to file.err for any command

  • 0 = write all errors to file.err

  • 1 = only write displayed errors to file.err

• 25 = kystop

  No information is provided.

• 26 = icloads (26)

  Key to forbid the iclist command from listing solution data instead of the input data.

  • 0 = iclist is OK

  • 1 = do not permit iclist

• 27 = ifkey error (27)

  key on whether or not to abort during /input on error.

  • 0 = do not abort

  • 1 = abort

• 28 = intrupt (ER_INTERRUPT)

  Interrupt button, so executable returns no error.

• spare - spare integer variables

pnamestr

Name of the variable where the queried value is stored.

**kwargs

Extra arguments to be passed to Mapdl.run.

Returns:

int or str

Value corresponding to key.