CFX pressure data mapping to structural blade

The objective of this test is to demonstrate CFX pressure data mapping to structural 11 blade model in PyMAPDL.

Description

The 11 blade model along with a fictitious disk is modeled. CFX generated pressure data is used as input.

The test uses a CFX exported pressure data to map. Pressure file correspond to a certain vibrating blade mode (vibrating mode 1 approximately 534 Hz)and to a certain pressure mode (pressure mode 1 also the same 534 Hz mode). However, due to lack of data for another mode this same file will be assumed to represent other mode combinations (vib mode 2 press mode 2) (vib mode 1 press mode 2) (vib mode 2 press mode 1).

from datetime import datetime

from ansys.mapdl.core import launch_mapdl
from ansys.mapdl.core.examples import download_cfx_mapping_example_data

Downloading files

files_path = download_cfx_mapping_example_data()

db_file_path = files_path["model"]
pressure_file_path = files_path["data"]

Launch MAPDL service

mapdl = launch_mapdl()

mapdl.title(
    "Verify Pressure Data Mapping exported from CFX on Structural 11 Blade Model"
)

TITLE=
 Verify Pressure Data Mapping exported from CFX on Structural 11 Blade Model

Upload files to the instance

Uploading files

mapdl.upload(db_file_path)
mapdl.upload(pressure_file_path)

Uploading ExampleMapping.db:   0%|          | 0.00/24.6M [00:00<?, ?B/s]
Uploading ExampleMapping.db: 100%|██████████| 24.6M/24.6M [00:00<00:00, 404MB/s]

Uploading 11_blades_mode_1_ND_0.csv:   0%|          | 0.00/828k [00:00<?, ?B/s]
Uploading 11_blades_mode_1_ND_0.csv: 100%|██████████| 828k/828k [00:00<00:00, 306MB/s]

'11_blades_mode_1_ND_0.csv'

Pressure mapping

Resume the database from the example mapping file

mapdl.resume("ExampleMapping", "db")
mapdl.esel("s", "type", "", 1)
mapdl.cm("BladeElem", "elem")

# Write CDB file
mapdl.allsel()
mapdl.cdwrite("all", "baseModel", "cdb")
mapdl.finish()

# Start the mapping processor and record the start time
start_time = datetime.now()
mapdl.slashmap()  # mapdl.slashmap(**kwargs); Enters the mapping processor.
print("Enter the Mapping Processor")

# Specifies the target nodes for mapping pressures onto surface effect elements.
mapdl.run("target,pressure_faces")

# Specifies the file type and pressure type for the subsequent import of source points and pressures.
mapdl.ftype(filetype="cfxtbr", prestype="1")
# Read the CFX exported file containing pressure data Blade 2, Export Surface 1
mapdl.read(fname="11_blades_mode_1_ND_0.csv")

# Perform the pressure mapping from source points to target surface elements.
# Interpolation is done on a surface (default).
print(mapdl.map(kdim="2", kout="1"))

Enter the Mapping Processor
MAP SOURCE DATA TO TARGET NODES
  INTERPOLATE ON A SURFACE
  MAXIMUM NUMBER OF NEAREST POINTS TO EXAMINE=  20
  SET RESULTS OUTSIDE OF REGION TO ZERO

 NON-ZERO PRESSURES APPLIED TO  9963 TARGET FACES (OUT OF 10622 DEFINED BY SURF154s)
  MIN REAL PRESSURE =  -2816.        MAX REAL PRESSURE =   4408.
  MIN IMAG PRESSURE =  -5189.        MAX IMAG PRESSURE =   5754.

Plot mapping

Plot the geometries and mappings

mapdl.show("png,rev")
mapdl.plgeom(item="BOTH")  # Plot both target and source geometries (default).
mapdl.plmap(item="target")
mapdl.plmap(item="target", imagkey="1")
mapdl.plmap(item="source")
mapdl.plmap(item="source", imagkey="1")
mapdl.plmap(item="both")
mapdl.plmap(item="both", imagkey="1")

# Close the plot and write the mapped data to a file
mapdl.show("close")
mapdl.writemap("mappedHI.dat")

# Print the mapping completion message and duration
print("Mapping Completed")
end_time = datetime.now()
c = end_time - start_time
seconds = c.total_seconds()
print("\nDuration in seconds for Mapping is  : ", seconds)

mapdl.eplot()

Mapping Completed

Duration in seconds for Mapping is  :  1.815246

Stop MAPDL

mapdl.finish()
mapdl.exit()